12/25/2023 0 Comments Repetier server load a windows startupThe Di3 with a stock Melzi mainboard have a few changes compared to other boards, specific to the Voltage divider's reference resistor. The sensor type you changed should match the actual sensor type and setup the printer uses. I'll continue to test.ġ4:14:41.068 : Printed filament:0.00m Printing time:0 days 0 hours 0 minġ4:16:39.995 : Printed filament:0.00m Printing time:0 days 0 hours 0 min I'm not sure how critical these are, because I seem to have basic functionality. So Repetier Host now connects, but there are some errors at the start, see below for a dump. Perhaps I have a flakey USB cable that is generating some errors at 115K? I really don't know what this is about, because the 115200 coms in my test app seem to work fine. I changed the 16mhz upload speed to 57600 and the upload worked straight away. I noticed that the 'upload.speed' setting for the 16mhz board was 115200, while the 8mhz board was 57600. I examined the boards.txt file in the board support folders for the sanguino. Thanks in advance for any advice you can give me.įor those of you who can't wait to hear the next installment in my saga: However, all my attempts to compile the 0.91 code for this board have also failed, and you seem to know what you're doing. At this point I'm not really concerned about getting the latest and greatest code, just something that works like my old board did. I added support for the board by copying the Sanguino folder from the Repetier GitHub repo.Īny idea what I'm doing wrong? Ultimately, all I'm trying to do is get a replacement Mezi board up and running in my Maker Select (Duplicator i3). ![]() The board selected in the IDE is "Melzi 1284p 16mhz". I'm using Arduino IDE 1.0.6 (because of all the posts I saw about only using this version). text will not fit in region textĭ:/programs/arduino/hardware/tools/avr/bin/./lib/gcc/avr/4.3.2/././././avr/bin/ld.exe: region text overflowed by 4520 bytes (Sorry for my poor Engligh too but i'm Portuguese).I'm trying to compile your version and I'm getting an error indicating it's too big:ĭ:/programs/arduino/hardware/tools/avr/bin/./lib/gcc/avr/4.3.2/././././avr/bin/ld.exe: section. I'm sorry but i'm such a noob so please treat me aswell Then I writted the next command but i got "cp: impossível analizar (.) No such file or directory". So, I opened the ROOT terminal and writed So if 250000 baud does not work try 115200. ![]() Some printer this works and for some not. It is more that I manually change some internal settings. I have used some tricks to allow non ansi baud rates. The init script already contains this command, so this is only an issue if you are # what(): locale::facet::_S_create_c_locale name not valid # terminate called after throwing an instance of 'std::runtime_error' Some people had problems with the boost::filesystem library used. If you have problems check the syslog or start the server directly without the -daemon Prompt without the -daemon parameter to get the output directly on your console. If you have problems you should read /var/log/syslog or start the server from command If you followed the installation instructions you can now access the server with your > sudo /etc/init.d/Repetier-Server restart Now your start script is active on next reboot. > sudo update-rc.d Repetier-Server defaults > sudo chmod 755 /etc/init.d/Repetier-Server linux/Repetier-Server.init /etc/init.d/Repetier-Server languages/* /var/lib/Repetier-Server/languagesĬreate a start init script to run the server as daemon upon boot time. dev/serial/by-id/usb-FTDI_FT232R_USB_UART_A800f4AP-if00-port0Ĭopy the content of www and languages to the created directories Use instead the /dev/serial/by-id/ like this for a device: The device name /dev/ttyUSBxx may change depending on the order the printer is enabled. > sudo mkdir /var/lib/Repetier-Server /var/lib/Repetier-Server/configs /var/lib/Repetier-Server/www /var/lib/Repetier-Server/storage /var/lib/Repetier-Server/languagesĬreate configurations for your printer in /var/lib/Repetier-Server/configs. The distribution works with the Debian-Wheezy linux version for the pi!Ĭreate a environment where the server can store it's data and printer configs. ![]() ![]() Code: Select all Installation instructions for this binary distribution for the Raspberry-Pi
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |